- Visitors can check out the Forum FAQ by clicking this link. You have to register before you can post: click the REGISTER link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. View our Forum Privacy Policy.
- Want to receive the latest contracting news and advice straight to your inbox? Sign up to the ContractorUK newsletter here. Every sign up will also be entered into a draw to WIN £100 Amazon vouchers!
Reply to: PC won't post/boot
Collapse
You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:
- You are not logged in. If you are already registered, fill in the form below to log in, or follow the "Sign Up" link to register a new account.
- You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
- If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.
Logging in...
Previously on "PC won't post/boot"
Collapse
-
As ee61r says this can be caused by one faulty board. After a lighting strike on the telephone cable my PC would not boot. Took out the network card and it was ok apart from that slot.
-
I have a PC Chips ML810 that fails to start sometimes so I have to clear the CMOS settings before it will start up again. There should be a marked jumper to short otherwise remove the CMOS battery for a few minutes and see if that helps.
Leave a comment:
-
Anything written on the PCB around the light?
I had this issue on my home server, till I read the writing above the light - turned out to be a loose piece of RAM.
Leave a comment:
-
Motherboard, PSU or CPU are likely culprits.
If there is some kind of PSU issue, or a short circuit detected at power on, it will shut down to prevent further damage.
Start by disconnecting PSU connections to all components except the motherboard (hard drive, DVD drive, graphics card, etc)
Then power on - see if it does more.
If it does, then the issue may be one of the unplugged components, or it could be one of the PSU outputs (they are various voltages, polarities, etc)
plug each component back in and power on, one component at a time until it breaks again.
If nothing more happens with everything disconnected, then remove and re-seat the CPU and try again.
Rob
Leave a comment:
-
PC won't post/boot
Ok so I've had the lid off.
When it tries to start the CPU and PSU fans spin briefly then stop. No beep, nada. There is an orange light that remains lit on the mboard.
Any ideas?
TIATags: None
- Home
- News & Features
- First Timers
- IR35 / S660 / BN66
- Employee Benefit Trusts
- Agency Workers Regulations
- MSC Legislation
- Limited Companies
- Dividends
- Umbrella Company
- VAT / Flat Rate VAT
- Job News & Guides
- Money News & Guides
- Guide to Contracts
- Successful Contracting
- Contracting Overseas
- Contractor Calculators
- MVL
- Contractor Expenses
Advertisers
Contractor Services
CUK News
- Why contractors keep putting off their pension (and why I'm one of them) Today 02:43
- HMRC loan charge settlement offer: 3 things to check before you sign Yesterday 07:41
- HMRC standstill agreements extended to 72 months: why the term's doubled, and what to check before signing Jul 31 05:53
- Who owns the loans? Inside the mystery of the loan charge recall scandal Jul 30 06:20
- Umbrella company winding-up petitions in 2026: the practical guide for contractors Jul 29 05:29
- Payments on Account deadline: what contractors must do before July 31st — maybe for the final few times Jul 28 08:01
- Andy Burnham's first 100 days: five things contractors need from the new PM Jul 27 00:53
- Starmer vs Burnham on housing: What their rival plans mean for your contractor mortgage Jul 22 00:59
- Burnham's housing vision vs. Starmer's home-buying reforms: what it means for your contractor mortgage Jul 22 00:59
- In Khalil v Innovate Transport, a limited company contractor wasn’t a worker and was on £2.30 — not £230 Jul 21 07:58

Leave a comment: