Sun T3+ array issue

Visitors can check out the Forum FAQ by clicking this link. You have to register before you can post: click the REGISTER link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. View our Forum Privacy Policy.
Want to receive the latest contracting news and advice straight to your inbox? Sign up to the ContractorUK newsletter here. Every sign up will also be entered into a draw to WIN £100 Amazon vouchers!

You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:

You are not logged in. If you are already registered, fill in the form below to log in, or follow the "Sign Up" link to register a new account.
You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

mudskipper replied

3 April 2014, 23:27
If you type Ctrl/T during boot, you can enter diagnostic mode and reset the config.

HTH.
Leave a comment:
BlasterBates replied

2 April 2014, 19:48
Have you tried thumping it?
Leave a comment:
Platypus replied

31 March 2014, 19:16
Meh, Sun ...
Leave a comment:
stek replied

31 March 2014, 18:35
Originally posted by eek View Post

I know its no help but.....

have you switched it off and on again.....

I fixed it! I read pages and pages, pdfs, web, the lot, only one mentioned the Ctrl-T option on boot to enter diags and wipe the config.
Leave a comment:
eek replied

31 March 2014, 12:09
I know its no help but.....

have you switched it off and on again.....
Leave a comment:
stek started a topic Sun T3+ array issue

30 March 2014, 21:27
Sun T3+ array issue

Driving me mad!

It's obviously been part of some partner array, now I'm trying to reset it and use it for another purpose. Trouble is I can't break into it, I can get to EEPROM, set up the params, set the password etc, boot tftp but it's looking for config data on the disks - which are no longer there...

No matter what I do I can't set the password, any ideas?

T3B Release 3.2.5 Thu Aug 24 02:10:28 PDT 2006 (192.168.1.30)
Copyright (C) 1997-2005 Sun Microsystems, Inc.
All Rights Reserved.

Initializing software...
Mounting tmp volume...
Starting RAS Daemons...
Found units: [u1-ctr]
Disk 2 Not Present (Enclosure 1)
Disk 3 Not Present (Enclosure 1)
Disk 4 Not Present (Enclosure 1)
Disk 5 Not Present (Enclosure 1)
Disk 6 Not Present (Enclosure 1)
Disk 7 Not Present (Enclosure 1)
Disk 8 Not Present (Enclosure 1)
PS2_NOBATT: Power Supply 2 Battery Not Present (Enclosure 1)
Default master is u1
Starting Heartbeats...
Assigning Select IDs: u1(1)
Initializing system drivers...
Initializing XPT component...
Initializing QLCF component...
Initializing loop 1 ISP2200 ... firmware status = 3
Detected 3 FC-AL ports on loop 1
loop 1 TARGET_ID = 0x0 (ALPA = 0xef)
Initializing loop 2 ISP2200 ... firmware status = 3
Detected 3 FC-AL ports on loop 2
loop 2 TARGET_ID = 0x0 (ALPA = 0xef)
Initializing SVD services...
Detected data cache size in system: 1GB
Testing ISP2200/ISP2310... Passed
Testing ECC mechanism... Passed
Testing XOR functions and datapaths... Passed
Cold Boot detected; destructive tests OK...
Testing data cache memory... Passed
Initializing Cache Memory...
u1d09 Unable to load configuration informationWARNING: Could not load u1 config data...
WARNING: u1 label init master error
ERROR: Cannot initialize enclosure u1
ERROR: Check hardware or run diags, then try rebooting...
Could not initialize system...
Power On Self Test failed...
Starting telnetd...
Starting pshd...
Starting psh...

Login:
Tags: None